+39 030 353 90 93 info@nuovadarimpianti.it

SLOW MIXER KVRL

SLOW INDUSTRIAL MIXERS
Agitatore lento KVRL con lanterna in materiale termoplastico per ambienti corrosivi

COATING SHAFT IN PP, PVC o PVDF

SLOW MIXER KVRL

Features:
– AISI 304-316 or C45 steel shaft, PP, PVC or PVDF coated, taped directly to the reducer
– Mechanical support with aluminum lantern for medium load (EVRK) or for high load (EVRL) and bearing
– Four-blade impeller with inclined, straight or high flow blades in AISI 304-316 steel or in PP, PVC, PVDF or PE-HD
– Single or double flushed mechanical seal on request.

      1. Agitatore lento KVRL con lanterna, disegno con i componenti numerati
      1. Shaft
      2. Coating
      3. Motor
      4. Reducer
      5. Lantern
      6. Bearing
      7. Impeller
      8. Impeller
      Agitatore lento KVRL con lanterna in materiale termoplastico per ambienti corrosivi

      STEEL SHAFT AISI 304-316

      IMPELLERS

      TITLED-BLADE MODULAR IMPELLER

      Range of use from 10 to 380 rpm.

      TILTED-BLADE TURBINE IMPELLER

      Range of use from 10 to 380 rpm.

      HIGH-FLOW IMPELLER

      Range of use from 10 to 380 rpm.

      MOVING FOUR-BLADE IMPELLER

      Range of use from up to 400 rpm.

      ANCHOR IMPELLER

      Use range from 5 to 56 rpm.

      SLOW MIXERS SET

      Agitatore lento verticale EVR in materiale termoplastico per ambienti corrosivi

      SLOW MIXER
      EVR

      Agitatore lento EVRK con riduttore in materiale termoplastico per ambienti corrosivi

      SLOW MIXER
      EVRK

      Agitatore lento EVRL con lanterna in materiale termoplastico per ambienti corrosivi

      SLOW MIXER
      EVRL

      Agitatore lento KVRL con lanterna in materiale termoplastico per ambienti corrosivi

      SLOW MIXER
      KVRL

      MORE INFO?

      KVRL: the slow mixer for heavy loads and large tanks

      The KVRL is the sturdiest slow mixer in our range. Compared with the EVR family the mechanical design changes: the shaft is flanged, it is supported by an iron lantern for heavy loads with a bearing, and the same shaft can carry 2 to 4 impellers, two-blade or four-blade, with inclined, straight or high-flow blades.

      Spreading several impellers along the shaft is the usual answer for tall tanks, where a single impeller would leave poorly mixed zones near the surface or the bottom. This makes the KVRL a good fit for large tanks, dense fluids and high mechanical loads. It also has the widest material choice in the range, ebonite included.

      • Flocculation in tall tanks
      • Neutralisation of large effluent volumes
      • Agitation of liquids with suspended solids
      • Storage and preparation of water treatment reagents
      • Mixing of high viscosity corrosive fluids

      Frequently asked questions

      How many impellers can the KVRL carry?

      The KVRL can run with a single impeller or with 2 to 4 impellers, two-blade or four-blade. Number, type and position are defined from tank height and fluid properties; inclined blade and high-flow impellers are listed for 10 to 380 rpm.

      Which materials are available?

      Flanged shaft in AISI 304-316 stainless steel or C45 steel coated with PP, PVC, PVDF, PE-HD or ebonite. Impellers in AISI 304-316 stainless steel, PP, PVC, PVDF, PE-HD or ebonite coated. The choice should be checked against the chemical compatibility of your product.

      How does the KVRL differ from the EVRL?

      The EVRL uses a high-load aluminium lantern and a four-blade impeller. The KVRL adds a flanged shaft, an iron lantern for heavy loads and the option of several impellers. Both accept a single or double flushed mechanical seal on request.

      Further reading

      FEEL FREE TO REACH OUT

      Call the phone number +39 030 353 90 93, from 9 to 12am and from 2 to 6pm